The Aquasol combination kit is available in one single pack for multiple parameters therefore in one single pack various parameters can be analyzed increasing the convenience and Portability.
Cooling Water Test Kit (AE 101)
Water is required to be cooled for many processes, for example air conditioners, manufacturing processes or power generation, etc. A cooling tower is used to reduce the temperature of a water stream by extracting heat from water and emitting it to the atmosphere. Cooling towers make use of evaporation whereby some of the water is evaporated into a moving air stream and subsequently discharged into the atmosphere. As a result, the remainder of the water is cooled down significantly. Water by its basic nature is corrosive. Therefore cooling systems are plagued with corrosion. Many factors affect corrosion rates in a given cooling water system. The presence of dissolved gases, chloride and sulfate levels, pH, alkalinity, scaling tendency, and protective ions such as calcium, magnesium, phosphate nitrate, and silicate must all be taken into consideration. The first step to control is detection therefore regular monitoring of the above is essential.
| Parameter | Range |
| Total Hardness | 2–40, 5–100, 25–500 mg/l as CaCO3 |
| Calcium Hardness | 5–100 mg/l as CaCO3 |
| Alkalinity | 10– 200 & 100–2000 mg/l as CaCO3 |
| Chloride | 10–200 & 50–1000 mg/l as Chloride |
| pH | 4 to 10 |
| Iron (Low Level) | 0.0,0.05,0.1,0.3,0.4,0.5,0.7,1.0,1.5,2.0 Mg/l as Fe |
| Silica | 5, 10, 20, 40, 60, 80 mg/l as SiO2 |
| Orthophosphate | 0, 5, 10, 20, 30, 40 mg/l as PO4 |
| Free Chlorine | 0.1-2.0 mg/l as Chlorine |
Boiler Test Kit (AE 102)
Boilers are systems which generate steam, which consists of two principal parts: the furnace, which provides heat, usually by burning a fuel, and the Boiler proper, a device in which the heat changes water into steam. The steam or hot fluid is then recirculated out of the boiler for use in various processes for heating applications. Proper pre-treatment of Boiler feed water is an important part of operating and maintaining a boiler system. As steam is produced, dissolved solids become concentrated and form deposits inside the boiler. This leads to poor heat transfer and reduces the efficiency of the boiler. Dissolved gasses such as oxygen and carbon dioxide will react with the metals in the boiler system and lead to boiler corrosion. In order to protect the boiler from these contaminants, they should be eliminated or at least through external or internal treatment.
| Parameter | Range |
| Total Hardness | 2-40, 5-100, 25-500 mg/l as CaCO3 |
| Calcium Hardness | 5–100 mg/l as CaCO3 |
| Alkalinity | 10-200 & 100-2000 mg/l as CaCO3 |
| Chloride | 10–200 & 50–1000 mg/l as Chloride |
| pH | 4 to 10 |
| Iron (Low Level) | 0.05, 0.1, 0.3, 0.4, 0.7, 1.0, 1.5, 2.0 mg/l as Fe |
| Silica | 5, 10, 20, 40, 60,80 mg/l as SiO2 |
| Orthophosphate | 0, 5,10, 20, 30, 40 mg/l as PO4 |
| Sulphite | 5-100 mg/l as Na2SO3 |
Drinking Water Test Kit (AE 103)
Drinking water is supposed to be safe for consumption by humans and animals. Water may be naturally safe, or it may need to be treated in order to be safe. Water which is not safe to drink can carry diseases and heavy metals.
| Parameter | Range |
| pH | 4 to 10 |
| Alkalinity | 10-200 & 100-2000 mg/l as CaCO3 |
| Total Hardness | 2-40, 5-100 mg/l as CaCO3 |
| Fluoride | 0.2–2.0, 0.5–5.0 mg/l as Fluoride |
| Nitrate | 1.0, 2.5, 5, 7.5, 10, 20, 30, 40, 50 mg/l as NO3 |
| Chloride | 10–200 & 50–1000 mg/l as Chloride |
| Iron (Low Level) | 0.05, 0.1, 0.3, 0.4, 0.7, 1.0, 1.5, 2.0 mg/l as Fe |
| Free Chlorine(DPD) | 0.1-2.0 mg/l as Chlorine |
| Turbidity | 1, 5,10, 25 as NTU |
RO Water Test Kit (AE 104)
Reverse Osmosis (RO) is a modern process to purify water for a wide range of applications, including semiconductors, boiler feed water treatment, food processing, biotechnology, pharmaceuticals, power generation, seawater desalting, and municipal drinking water.
| Parameter | Range |
| pH | 4 to 10 |
| Total Hardness | 2-40, 5-100, 25-500 mg mg/l as CaCO3 |
| Calcium Hardness | 5-100 mg/l as CaCO3 |
| Silica | 5, 10, 20, 40, 60, 80 mg/l as SiO2 |
| Sulphate | 5–100, 50–1000 mg/l as Sulphate |
| Iron (Low Level) | 0.05, 0.1, 0.3, 0.4, 0.7, 1.0, 1.5, 2.0 mg/l as Fe |
| Nitrate | 1.0, 2.5, 5, 7.5, 10, 20, 30, 40, 50 mg/l as NO3 |
| Nitrite(Low Level) | 0.04-0.8 mg/l as NO2 |
Swimming Pool Kit Test (AE 105)
Swimming pool water is a carrier of harmful bacteria. Hence, microbiological quality is the most important parameter for the safety of swimming pool water. Therefore there is broad consent that disinfection of pool water is indispensable. Concentration of free chlorine in swimming pool water is necessary to achieve this goal.
| Parameter | Range |
| Free Chlorine | 0.5 – 5.0 PPM as Chlorine |
| pH | 6.5 to 9 as pH |
Purified Water Test Kit (AE 106)
Highly purified water is an essential component of biopharmaceutical industry. It is used as an ingredient in both research procedures and drug formulations and also for general cleaning, rinsing, etc. In each case the water source must be processed and treated to microbial and chemical contaminants that would otherwise compromise the quality, safety, efficacy and purity of finished product.
| Parameter | Range |
| Acidity | 10-200 & 100-2000 mg/l as CaCO3 |
| Alkalinity | 10-200, 100-2000 mg/l as CaCO3 |
| pH | 4 to 10 |
| Calcium, Magnesium | 5-100 mg/l as CaCO3 |
| Ammonium | 0.5, 1.0, 2.0, 4.0, 6.0, 8.0 mg/l as NH4 |
| Sulphate | 10-200, 50-1000 mg/l as Sulphate |
| Chloride | 10-200, 50-1000 mg/l as chloride |
| Heavy Metal as Pb | NA |
Metal Working Fluid Test Kit (AE 107)
Water is the major ingredient in a water soluble metalworking fluid mix. It may amount to as much as 90-99% of the mix as used. Therefore, its importance in product performance can not be ignored. Corrosion, residue, scum, rancidity, foam, excess concentrate usage, or almost any metalworking fluid performance problem can be caused by the quality of the water used in making the mix. Untreated water always contains impurities. Some impurities affect drastically by reacting or combining with metalworking fluid ingredients. These impurities can change performance characteristics. Therefore, water treatment is necessary to obtain the full benefits of water soluble metalworking fluids.
| Parameter | Range |
| Total Hardness | 2-40, 5-100 mg/l as CaCO3 |
| Chloride | 10-200 & 50-1000 mg/l as Chloride |
| pH | 4-10 |